Parts and Keys

How a Typewriter Ribbon Works: Spools, Ribbon Vibrator and Reverse Lever

How a typewriter ribbon works: the spools that wind it, the ribbon vibrator that lifts it, the reverse lever, the color selector, and common ribbon problems.

On this page
  1. What the ribbon does
  2. Spools: how the ribbon is stored and moved
  3. Ribbon vibrator (ribbon lift)
  4. Reverse lever and auto-reverse
  5. Color selector and stencil position
  6. Spools vs cartridges, and choosing a ribbon
  7. Ribbon trouble
  8. Related reading

What the ribbon does

A typewriter ribbon is a strip of fabric soaked with ink. When a typebar strikes it, ink transfers from the ribbon to the paper in the shape of the character. Without a ribbon, the typebar would only press an impression into the paper.

Spools: how the ribbon is stored and moved

Most manual typewriters use two spools, one on the left and one on the right. The ribbon is wound on one spool and travels across the front of the machine to the other. A ribbon moves a short distance each time you press a key, so fresh ink is always presented to the next character.

Some machines instead use a cartridge or a single enclosed spool. A cartridge is easier to install, but it must be made for your type of machine.

Things to know about spools:

  • Spools are not all the same size. Spools from one machine do not always fit another. Check what your model requires, and note the ribbon width.
  • Spools carry the ribbon’s direction of travel. If the ribbon is wound the wrong way, it may not feed correctly. Step-by-step threading is covered in how to load and replace a typewriter ribbon.
  • Metal and plastic spools exist. Older machines often have metal spools.

A spool drive, usually a ratchet connected to the typing mechanism, turns the active spool a small step with each keystroke.

Ribbon vibrator (ribbon lift)

The ribbon vibrator, also called the ribbon lift or ribbon carrier, is a small fork-shaped guide at the printing point. The ribbon passes through it. When you press a key, a linkage raises the vibrator, lifting the ribbon between the typebar and the paper. When the key is released, the ribbon drops back down so you can see what you typed.

Because of this, the ribbon sits low at rest and rises only for each strike. If the vibrator is bent, stuck or misadjusted, you may get faint print at the top or bottom of characters, or no print at all.

Reverse lever and auto-reverse

The ribbon only travels in one direction at a time. When the ribbon has mostly moved to the take-up spool, the direction must be reversed so it can feed back the other way. This is done with the reverse lever.

  • Manual reverse: you flip a lever or switch. The ribbon can then travel in the opposite direction.
  • Automatic reverse: many machines have a mechanism that detects the end of the ribbon, often by a metal eyelet or a notch in the ribbon. It switches direction on its own. If your machine does this, a damaged or missing eyelet can stop it from working.

If your ribbon winds all onto one spool and then stops, the reverse mechanism is a likely suspect.

Color selector and stencil position

Many machines can use two-color ribbons, usually black and red. A ribbon color lever shifts the ribbon up or down so that either the upper or lower half is at the printing point. Many machines also have a stencil (or white) position, which stops the ribbon from lifting so the type hits the paper directly. This was used for cutting stencils, and it is also useful for cleaning type without inking.

Spools vs cartridges, and choosing a ribbon

  • Check your machine’s manual or make and model for ribbon type and width.
  • Ribbons are commonly made of nylon or cotton, and some are made from silk. Nylon is typically more durable.
  • A universal ribbon may fit many machines, but check that it fits your spools and the ribbon width. See where to buy typewriter ribbons.
  • Store unused ribbons away from heat and sunlight so they do not dry out.

Ribbon trouble

  • Faint print: the ribbon may be dried out or worn. Also check the ribbon vibrator.
  • Ribbon not advancing: check that the spools turn and the reverse lever is not stuck in neutral.
  • Ribbon tearing or jamming: may come from rough spool edges, a bent guide or a ribbon not threaded correctly.
  • Double or smudged impressions: these may be unrelated to the ribbon. See Key Rebound on a Typewriter.

The complete guide to parts and keys

Parts of a Typewriter: A Complete Anatomy Guide
Read the guide

Keep exploring

Guides from other topics

All topics →