Before you start
The exact process depends on your machine, so treat this as a general outline and check your manual if you have one. Many manuals are available online. Most manual typewriters use the same basic idea: a ribbon wound on two spools, passing in front of the paper through a small slot or fork, called the ribbon vibrator, that lifts the ribbon as each key strikes.
You will need a new ribbon, a clean cloth, and a bit of patience. A phone camera is useful for taking pictures as you go. Work on a clean table, and put a cloth or paper under the machine, because used ribbons can stain.
Check what kind of ribbon your machine uses
Before you buy or load a ribbon, identify what your machine takes:
- Spool type. Most vintage manuals use a ribbon on two open metal or plastic spools. Spool size and shape vary between brands, and some machines will not accept a spool from another.
- Cartridge type. Many electric and electronic typewriters use a plastic cartridge that drops in. These are model-specific, so you generally need the correct part number.
- Ribbon width. The most common width on manuals is about half an inch (12–13 mm), but some machines use different widths.
- Material. Ribbons are usually fabric (cotton or nylon) or, on some electrics, a single-use film (carbon) ribbon.
If you are buying, see where to buy typewriter ribbons, paper and correction supplies.
Remove the old ribbon
- Take a photo of the ribbon path before touching anything, or sketch how it is threaded.
- Lift or remove the machine’s cover if needed.
- Move the ribbon vibrator or carrier into a position where you can reach it. On many machines it comes up if you press a key slightly or use a lever.
- Slide the ribbon out of the guides and the vibrator.
- Lift the spools off their spindles. Some are held by a clip, cap or small lock, and some lift straight off. If a spool is stuck, rock it gently from side to side, and do not pull it with force.
Keep the old spools. Many vintage machines come with metal spools you can reuse, and a new ribbon may be supplied on a spool that doesn’t fit your machine.
Load the new ribbon
- Transfer the ribbon to your machine’s spools if needed. If the new ribbon is sold on a different spool, you can usually unwind it from that spool and wind it onto your machine’s spool, keeping the ribbon flat and not twisted. Do this by hand, slowly, and avoid kinks.
- Attach one end to an empty spool. Ribbons usually have a small hole or eyelet at each end, or you hook the end into a slot on the spool. Look at how the old spool was attached.
- Wind some ribbon onto the empty spool, a few turns is enough to hold it.
- Place both spools on the spindles in the same orientation as before.
- Thread the ribbon through the guides and the vibrator, following your photo. The ribbon should lie flat and face the right way, with the ink side facing the paper path.
- Lock the spools and replace any covers.
Make sure that the ribbon runs smoothly and isn’t caught on any metal edge. Turn a spool by hand to check that it advances.
Set the ribbon selector and test
Many typewriters have a ribbon selector with positions for upper colour, lower colour and stencil. For a single-colour black ribbon, use the position marked for the ribbon colour. The stencil or “no ribbon” position is for cutting stencils and prints no ink, so leave it unselected.
Type a few lines on a sheet of paper. A new ribbon should print clearly and evenly. Watch both spools while you type: the ribbon should move along as you type, and when one spool is nearly empty, the machine’s reverse mechanism should automatically switch direction. On many machines, small eyelets at the ends of the ribbon trigger this. If the ribbon runs off the end, it may be because the reverse lever is stuck or the ribbon was threaded the wrong way.
Re-inking an old ribbon
If you can’t get a new ribbon, some people re-ink an old fabric ribbon with stamp-pad ink, applying a drop at a time and letting it spread, while others use a light spray of lubricant. Results vary, and too much ink or oil makes a smeared mess. You cannot re-ink a carbon (single-use film) ribbon. A ribbon that is frayed, torn or has mould should be replaced and not reused. For ordinary use, a new ribbon is usually the better choice.
Common problems
- Faint print: The ribbon may be dry. Also check that the ribbon selector is set correctly and that the type slugs aren’t clogged with old ink.
- Ribbon doesn’t advance: The spool may not be locked on the spindle, or the ribbon may be caught in a guide.
- Ribbon doesn’t reverse: Look at the reverse lever, and check that the ribbon ends are attached correctly.
- Ribbon jams or bunches: Rewind the slack and make sure it isn’t twisted.
- Smudged letters: Clean the typeface gently with a soft brush. Do not use harsh solvents without checking your model’s guidance.
If problems continue after a fresh ribbon is loaded correctly, the cause may be mechanical, and it may be time for a service by a repair person. If you’re still deciding whether to get a machine, see using a typewriter today.